CAGEVISION

Facility setup

Setting up your bar.

For a facility that has bought a CageVision bar. Where it goes in the cage, what to have ready, and what happens on install day, step by step.

Coach guide

01

How install works today

The CageVision team installs every bar with you, on site. Setup takes part of a day, most of it with the cage empty. Every step on this page is marked:

  • You something you or your staff do.
  • CageVision team the CageVision team does this for you during install.

The iPad app has a guided setup for every step (gear › Calibrate › Facility setup). Over the coming months more of the team's steps move into that flow, so a facility can set up a bar by itself. Until then, the team does them.

02

Have these ready

WhatWhy
The cage, with its lights workingThe cameras need the cage lights on to see a fast ball. Light is part of the measurement.
A regulation 17-inch home plateThe bar sets up the whole cage from the plate. If yours is a bigger mat or has a tape outline around it, tell us before install day.
A wall outlet behind the plateThe bar plugs into its power box. Plan where the cord runs so nobody trips on it.
An iPad for the cageIt's the controller and the board. Install the CageVision app from the App Store before we arrive.
Your facility Wi-Fi name and passwordThe bar has no internet. The iPad carries numbers and video to the cloud over your Wi-Fi at the end of the day.
Each coach's emailSo we can add every coach to your facility (see Coach accounts).
A tape measure, a tee and a few baseballsFor the tee check, the drop test and the test swings.
Your pitching machine, if you use oneWe tape where the ball comes out so the bar knows where pitches start.
A hitter for 10 minutesThe last step is 10 real tee swings.
03

Where the bar goes

Behind the plate89 in

From the back point of the plate to the front of the lenses (7 ft 5 in). Farther is fine if the net forces it. Never closer.

CenteredOn the line

On the plate's center line, looking straight out toward center field.

Outside the netAlways

The bar stands outside the backstop net, with clear space between the net and the lenses.

Side view: the bar stands outside the backstop net, 89 inches behind the back point of home plate, with the cameras looking out toward the field. NET BAR PLATE 89 in FIELD →
Side view, not to scale. The 89 inches run from the plate's back point to the lens fronts.
  • Both cameras must see the whole plate. At 89 inches the top camera just sees the plate's front edge, which the bar uses to check its own setup. Closer than that, the setup check fails.
  • Keep the net off the lenses. Net strands right on the lenses hide the ball. Never cut the net, and never put the bar inside it to get closer.
  • Set the base level and tape its outline on the floor, so it can go back to exactly the same spot.
  • Keep the iPad where it can see the bar. The bar's own Wi-Fi reaches the cage, not the whole building.
  • Turn the whole bar, never a camera, and never touch a lens ring. The cameras' angles are set at the factory.
04

The 8 setup steps

This is the order on install day. In the app the steps are under gear › Calibrate › Facility setup. You can stop and pick up where you left off at any step. Keep the cage empty until step 8.

Before step 1 CageVision team Moving a bar, even in a car, can shift its two cameras slightly against each other. At every new site the team re-checks the cameras against each other with a large checkerboard before anything else.

STEP 1Connect YouCageVision team

Plug in the power box and press its button. On the iPad, join the CageVision Wi-Fi (the team gives you the password) and open the app. Sign in, choose Coach, and the app finds the bar.

The setup checks the bar's clock against the iPad and checks that both cameras are sending pictures at full speed. The first few minutes after power-on are a warm-up; the app counts it down.

Today the team sets the bar's clock and checks the cameras by hand.

STEP 2Place the bar You

Put the bar where the section above says. The app shows a live picture from each camera. Tape the distance from the plate's back point to the lenses and enter it.

Done when: both cameras show the whole plate.

STEP 3Light CageVision team

The bar takes pictures from both cameras and checks that the mat, the plate and a ball on the tee all show clearly, without glare washing out the plate. If your building is brighter or darker than usual, it adjusts the brightness for your facility only.

Done when: under 3% of the picture is washed out.

STEP 4Plate click YouCageVision team

The app shows the bottom camera's picture. Tap the plate's five corners (front left, front right, right corner, back point, left corner), zooming in with +. If a net strand covers a corner, put the dot where the two edges meet. Tap Solve. The bar checks your taps with both cameras before anything is saved. Then tap Apply; the bar restarts its measuring, about 35 seconds.

Done when: the bar accepts the click. A refused click saves nothing; zoom in and tap again. Today the team checks the result on both cameras and fits the top camera's view to your cage.

STEP 5Tee check You

Put a ball on the tee and keep everyone clear for 10 seconds. Tape the ball's height above the plate and enter it. The bar measures the same ball with its cameras.

Done when: the bar's height agrees with your tape within 1 inch.

STEP 6Drop test YouCageVision team

The bar checks its own speed scale by watching a ball fall. Stand over the plate, hold a ball as high as you can reach and let it go. Don't throw it. Do it three times, stepping back between drops, inside the countdown.

Done when: the measured gravity is within about 2% of the real thing, which means exit speeds are right too. Today the team works out the result.

STEP 7Pitching machine YouCageVision team

No machine? Choose Tee only; you can add one later. With a machine, tape three numbers: from the center of the plate's front edge to where the ball comes out, how far that is toward third base, and how high the ball comes out.

You tape; today the team enters the numbers on the bar.

STEP 8Test swings You

A hitter takes ten tee swings. The app shows each one as it reads.

Done when: at least 8 of 10 read, the two cameras agree on the ball, and numbers reach the board in 3 seconds or less. Then the bar is live.

05

Wi-Fi: two networks

NetworkWhat it's for
CageVisionThe bar's own network. The cage iPad stays on it all session. It has no internet, on purpose: the bar works the same whether your building's internet is up or not.
Your facility Wi-FiUploads. At the end of the day the iPad switches to it, sends the day's numbers and video, and switches back. Enter it once in the app's Upload tab under Facility Wi-Fi; the app remembers it.

Any TV in the cage can show the board too: AirPlay from the iPad, or a TV on the CageVision network. See the coach guide.

06

Coach accounts

  1. You Each coach installs the CageVision app, creates an account with their email, and picks Coach when it asks who they are.
  2. You Send us the email each coach signed up with.
  3. CageVision team We add those accounts to your facility. From then on, any of your coaches can run sessions, upload, and answer families' swing reports from any phone or iPad. If we give you a facility ID, enter it under gear › Facility; otherwise leave that setting alone.

Hitters don't need accounts. Coaches add them on the iPad's Session page, and families connect with a parent email or a link code (see the coach guide).

07

Your first session

  1. Add a few hitters on the Session page, pick them, tap ▶ PLAY.
  2. Run tee groups first and machine groups last. After machine pitches the bar stays in machine mode for 5 minutes.
  3. At the end of the day run Upload, then shut down from the app before switching off the power box.

The coach guide covers a normal day in full. Print its one-page version for the cage wall.

08

After install

  • Don't move the bar or touch the cameras. If you need the bar somewhere else, even within the same cage, or it gets knocked, email us first. A moved bar needs setup again.
  • Keep it outside the net, and never cut the net.
  • Shut down from the app before cutting power.
  • Keep the lights on during sessions.

Software updates come through the iPad app. Questions or anything unusual: deo@cagevisionbaseball.com.

09

Wall mount for live at-bats CageVision team

Cages with a catcher and live pitching need the cameras above the action. For those, the bar's two cameras go on a beam mounted high on the back wall behind the plate. The CageVision team designs and installs this one with you, so this is only what to check in your building beforehand:

  • Height. The cameras sit 12 feet above the plate, tilted 30° down toward it. A 10-foot mount is the fallback.
  • Roof net. For the 12-foot mount it has to attach above about 12½ feet.
  • Backstop net. At camera height it has to hang at least 33 inches off the wall, including how far it bulges when a ball hits it. If it's closer, it gets tied forward to the cage frame, not cut.
  • The wall. Wood studs, poured concrete, concrete block or a steel column. Drywall alone or metal studs won't hold it.
  • The iPad mounts at hand height outside the net. Nobody needs to touch the beam to run a session.

Coach guide